Hisense fridge water filters

Hisense's UK fridge catalogue is not standardised the way Samsung or LG are: many small series each use their own filter reference rather than sharing one part across a wide range. Always confirm your exact model number before ordering.

How to identify your Hisense fridge

The rating plate with the full model number is inside the fridge compartment; because Hisense uses different filter references for different series, this exact model number is essential before ordering, more so than for most other brands on this site.

Water filters for Hisense fridges

Each reference below has its own page on this site with the full list of fridges it fits, the fitting steps and the mistakes that send people back to buy a second cartridge.

Filter reference	Fitting position	Change interval
DA2010CB	Internal cartridge	Every 6 months is the usual interval for this style of cartridge; check your fridge's own manual

Where Hisense owners go wrong

Assuming one Hisense filter reference covers the whole range the way Samsung's or LG's main references do: Hisense's catalogue is fragmented by series, and a reference confirmed for one model can be wrong for another.
Buying from a generic listing that names many Hisense models without a distributor or manufacturer source behind it.

When to change the filter

A six month change interval is the usual guidance across most cartridge filters of this type, but check your specific fridge's manual since Hisense does not publish one unified schedule across its range.

Hisense water filters: common questions

Why does this site only list one Hisense filter reference?

Because that is the only Hisense reference we could confirm against an official parts distributor. Other Hisense series use other, unconfirmed references, and publishing them without a verifiable source risks sending you to the wrong part.

See current Hisense water filter prices on Amazon UK

Before you remove the old cartridge

Set up the job before opening the filter housing. Most leaks and air lock problems start when the cartridge is removed while the water circuit is still under pressure or while the dispenser is still being used.

Allow 20 to 30 minutes for the whole job, including flushing the new cartridge.
Use a clean towel at least 500 mm by 700 mm, because a small hand cloth is often not enough for the first spill from an internal housing.
Keep a bowl or jug of at least 1 litre near the fridge to catch drips and to discard the first water from the dispenser.
Wash your hands before handling the new cartridge, especially the end that enters the fridge water circuit.
Do not use pliers on the cartridge body. If the cartridge will not turn by hand, stop and relieve pressure first.

If the fridge has a water shut off valve behind it or under the sink, close it before starting. If access is difficult, use the dispenser for 5 to 10 seconds after closing the valve to reduce pressure. Keep the fridge door open only as long as needed, as the work is usually inside the chilled compartment.

Replacement procedure and checks

For the confirmed Hisense cartridge listed on this site, use the model specific page for the final fitting direction and locking position: Hisense DA2010CB filter. The general work sequence below is useful for avoiding spills and installation errors.

Open the fridge compartment and clear the shelf space around the filter head. Leave at least 150 mm of hand clearance in front of the housing.
Place the towel directly under the filter area. A small amount of water in the housing is normal.
Support the filter head with one hand if it is exposed. Turn the old cartridge slowly with the other hand. Do not pull downward until it has released.
Keep the old cartridge upright after removal. It may still contain 100 to 300 ml of water.
Check that the old sealing ring has not stayed inside the filter head. A doubled seal can stop the new cartridge from seating correctly.
Insert the new cartridge squarely, then turn it only to the stop point. Forcing it past the stop can damage the plastic lugs.
Reopen the water valve, then dispense water in short runs. Use 5 to 10 second bursts with pauses between them for the first minute.

Flush until the flow is steady and clear. A practical figure is 3 to 5 litres for a domestic internal fridge cartridge unless the appliance manual states a different amount. During flushing, check the filter head, the base of the fridge compartment and the floor in front of the appliance.

Figures to use during the job

Check point	Practical figure	Why it matters
Working time	20 to 30 minutes	Includes access, replacement, flushing and leak checks.
Water to discard after fitting	3 to 5 litres, unless the manual says otherwise	Removes trapped air and loose carbon fines from the new cartridge.
First leak check	After 2 minutes under pressure	Small seal leaks often appear only after the housing fills fully.
Second leak check	After 30 to 60 minutes	A slow drip can take time to reach the shelf or floor.
Dispenser test	Several short bursts, not one long run	Reduces sputtering while air leaves the line.

Do not judge the installation only by the first glass of water. Air can remain in the line after the cartridge is seated. Sputtering for the first few litres is common, but water around the filter head is not normal and must be checked immediately.

Frequent faults, recovery steps and special cases

If the new cartridge will not lock, remove it and compare only the connection shape with the old cartridge. Do not trim plastic, lubricate the connector with cooking oil or file the lugs. If the shape differs, stop, because the wrong cartridge can damage the filter head.

If water flow is weak after replacement, confirm that the shut off valve is fully open, then dispense 2 to 3 more litres in short bursts. If the flow does not improve, remove the cartridge, inspect the seal, refit it squarely and test again. A cartridge that is not fully locked can restrict flow without leaking at first.

If the dispenser continues to spit air after 5 litres, check whether the fridge has recently been moved or the water supply line has been disturbed. A kinked plastic tube behind the appliance can reduce flow and draw air into the line. Pull the fridge forward only far enough to inspect the tube, usually 100 to 200 mm is enough for a visual check, and avoid crushing the line when pushing the fridge back.

If the appliance has an ice maker, discard the first full bin of ice after a filter change. This is separate from flushing drinking water, because water can remain in the ice circuit. If the fridge has been unused for more than 2 weeks, flush the dispenser before judging taste or odour. For general reset and troubleshooting questions, use the fridge water filter FAQ.